Canadian Onroad Nationals - Touring Car Rules

For further information
contact the race organizers at: mailto:conrc@digitaldetail.ca

@CdnNats

Touring Car Rules and Specifications

	Can-Am Stock (Handout)	Super Stock (17.5)	Modified (Open)
Race Length	5 minute Qualifiers 6 Minute Mains	5 minute Qualifiers 6 Minute Mains	5 minute Qualifiers 6 Minute Mains
Chassis	Any 1/10 scale, 190mm wide, 4wd touring car	Any 1/10 scale, 190mm wide, 4wd touring car	Any 1/10 scale, 190mm, 4wd touring car
Motor	Handout motor, supplied by the race organizers and to be returned after racing is concluded. Rental fee included in entry fees for this class. Capped Gear Ratio = Minimum FDR: 5.40	Any ROAR or BRCA approved 17.5 brushless motor. Motors must be on the published ROAR or BRCA approved list no less than 1 week prior to the final registration deadline to be permitted.	Any brushless motor (540 size can)
Speed Control	Any ROAR approved ESC that does not have timing advance settings, or ESC's that have a "spec mode" disabling timing advance and have a blinky light to show it's in a zero timin mode	Any ROAR approved ESC that does not have timing advance settings, or ESC's that have a "spec mode" disabling timing advance and have a blinky light to show it's in a zero timin mode	Any Electronic Speed Control
Weight	Minimum 1350gr	Minimum 1350gr	Minimum 1350gr
Tire/Rim	Gravity RC Type C is the Spec Tire for this class . One Set is included with your entry fee. Additional race tires must be purchased at the event ($40/set).	Gravity RC Type C is the Spec Tire for this class . One Set is included with your entry fee. Additional race tires must be purchased at the event ($40/set).	Gravity RC Type C is the Spec Tire for this class. One Set is included with your entry fee. Additional race tires must be purchased at the event ($40/set).
Ride Height	Minimum 5mm	Minimum 5mm	Minimum 5mm
Batteries	Any ROAR approved hard cased 2s, 7.4v nominal LiPo. Batteries can be tested at any time by officials and must not exceed a maximum of 8.40v.	Any ROAR approved hard cased 2s, 7.4v nominal LiPo. Batteries can be tested at any time by officials and must not exceed a maximum of 8.40v.	Any ROAR approved hard cased 2s, 7.4v nominal LiPo. Batteries can be tested at any time by officials and must not exceed a maximum of 8.40v.
Bodies	Any body that falls within the Global Body Spec parameters for 1/10 Scale, 190mm touring cars. The overall height of the body, mounted on the chassis, ready to race, is not to be under the minimum height of 115mm from the tech surface. Overall width of must not exceed 195mm. Wings - Only one wing is allowed, fixed to the rear truck lit. The rear edge of the wing or side dams may not extend beyond the rear of the body more than 10mm. No part of the wing may extend above the roofline of the body. No part of the wing may extend beyond the sides of the body.	Any body that falls within the Global Body Spec parameters for 1/10 Scale, 190mm touring cars. The overall height of the body, mounted on the chassis, ready to race, is not to be under the minimum height of 115mm from the tech surface. Overall width of must not exceed 195mm. Wings - Only one wing is allowed, fixed to the rear truck lit. The rear edge of the wing or side dams may not extend beyond the rear of the body more than 10mm. No part of the wing may extend above the roofline of the body. No part of the wing may extend beyond the sides of the body.	Any body that falls within the Global Body Spec parameters for 1/10 Scale, 190mm touring cars. The overall height of the body, mounted on the chassis, ready to race, is not to be under the minimum height of 115mm from the tech surface. Overall width of must not exceed 195mm. Wings - Only one wing is allowed, fixed to the rear truck lit. The rear edge of the wing or side dams may not extend beyond the rear of the body more than 10mm. No part of the wing may extend above the roofline of the body. No part of the wing may extend beyond the sides of the body.